首先要分清楚晶振还是晶体,晶振的话好像不用电容吧,晶体的话0.1u和0.01u的电容有些大了,一般应该100p到20p之间。
晶振的标称值在测试英文时还有带个个“负荷电阻”的能力,在作业时具备这是能力,震荡几率才与标称值保持一致。般来说,有低负荷电阻(结合谐振结晶)高负荷电阻(电解电感(电解电感器)电解电感关联集成运放设计图谐振结晶)之分。在集成运放设计板上的共同点为:晶振串一直电阻跨接在IC两个脚部的,则为结合谐振型;一直脚接IC,一直脚接地线的,则为电解电感(电解电感器)电解电感关联集成运放设计图型。如我认为没得原技术参数,必须代用的可利用结合谐振型集成运放设计板上的电阻再并带个电阻,电解电感(电解电感器)电解电感关联集成运放设计图谐振集成运放设计板上串一直电阻的办法。诸如:4.433MHz晶振,并一直3300PF电阻或串一直70P的调整电阻。其它种称法是“衰减值”与“激励员工电平”之分:
其实,上述原因都可以作为选择晶振的条件作为考虑。
常见的晶振大多是二只脚,3脚的晶振是一种集晶振和电容为一体的复合元件。由于在集成电路振荡端子外围电路中总是以一个晶振(或其它谐振元件)和两个电容组成回路,为便于简化电路及工艺,人们便研制生产了这种复合件。其3个引脚中,中间的1个脚通常是2 个电容连接一起的公共端,另外2个引脚即为晶振两端,也是两个电容各自与晶振连接的两端。由此可见,这种复合件可用一个同频率晶振和两个100~200pF的瓷片电容按常规连接后直接予以代换。
|